Upgrading my display cabinet

For special skills and tip to make collecting better
Post Reply
StevieSX
Posts: 269
Joined: Fri Sep 11, 2020 4:02 pm
Location: Ipswich
Contact:

Upgrading my display cabinet

Post by StevieSX »

Having decided to use some incoming cash to upgrade my display cabinet with additional glass shelving (finally getting rid of the temporary foam shelves), I've got pretty much every car packed away in it's box. Took a few evenings with 500 odd but it was quite satisfying. There are a few still out that never had boxes so most of those will get wrapped up and stored with the rest, barring a few where I've added little bits that will snap off if I try to do that.
20210319_000646.jpg
I am planning to put an LED strip at front and back of the underneath of each wooden shelf to give the cars some proper lighting and show the detail. I was then thinking, is it worth running some UV light strips along the edges as highlighted in the picture below?
20210319_000739.jpg
I'm unclear as to whether occasionally giving the models some UV light will help them. I've read that UV light will lead to damaging paint and fading plastic parts on models but also that white decals will yellow over time (at least older models) if they don't get any sunlight, so I'm a little unsure on this. I have a few models that have started to go a bit beige but then again, I can't recall now if I bought them like that or they have become that way in my car...paranoia setting in a little!

Any thoughts would be appreciated.
You do not have the required permissions to view the files attached to this post.

Alfaholic
Posts: 9209
Joined: Thu Mar 19, 2015 5:20 am
Location: Braidwood, Australia

Re: Upgrading my display cabinet

Post by Alfaholic »

Ohhhh, that look's like a shopping list - I'll have...... :lol: :lol:

Looking forward to seeing the outcome.
Martin

Tom
Posts: 29937
Joined: Fri Aug 23, 2013 9:29 am
Location: The Netherlands

Re: Upgrading my display cabinet

Post by Tom »

Impressive collection! Looking forward to the new display. I'm of the 'no UV' type myself.

JSB33
Site Admin
Posts: 45498
Joined: Mon Dec 29, 2008 11:25 am
Location: Bedford
Contact:

Re: Upgrading my display cabinet

Post by JSB33 »

Looks like you are at maximum capacity, no social distancing there :lol:
Jeff

StevieSX
Posts: 269
Joined: Fri Sep 11, 2020 4:02 pm
Location: Ipswich
Contact:

Re: Upgrading my display cabinet

Post by StevieSX »

Finally progressing on this with 16 glass shelves, a big old perspex screen and 5m of LED strip lights and the appropriate gear ordered.

The models have been stuck under my bed for months now (probably up to 100 that have never been on display) so it will be really nice to get progress towards displaying them again :D

StevieSX
Posts: 269
Joined: Fri Sep 11, 2020 4:02 pm
Location: Ipswich
Contact:

Re: Upgrading my display cabinet

Post by StevieSX »

Took a few pictures of some of the work in progress and bits that have arrived.
Unit Reinforced.jpg
The floating shelves have been fixed in place with additional black screws. The original fixed shelves with the silver screws have covers.
Shelf runners.jpg
Bought some basic black plastic angled moulding to act as shelf runners and these were cut to size and drilled for screws.
Runners in place.jpg
Starting to get the shelf runners in place.
You do not have the required permissions to view the files attached to this post.

StevieSX
Posts: 269
Joined: Fri Sep 11, 2020 4:02 pm
Location: Ipswich
Contact:

Re: Upgrading my display cabinet

Post by StevieSX »

Additional back support.jpg
A couple of bits of hardboard were cut to sit across the back and re-inforce the structure for the additional weight of the glass shelves and will also rest against the wall to be drilled through and fixed in place against the wall to avoid any tipping forward.
Glass Shelves.jpg
These glass shelves (16 of them, two lots of 2 and four lots of 3 for the gaps between the fixed wooden shelving) will rest on the runners.
You do not have the required permissions to view the files attached to this post.

StevieSX
Posts: 269
Joined: Fri Sep 11, 2020 4:02 pm
Location: Ipswich
Contact:

Re: Upgrading my display cabinet

Post by StevieSX »

LEDs.jpg
These will sit at the back and will be 45 degree angled downwards and to the front. 6 lots of around 75cm worth for the underneath of each wooden shelf.
Perspex door.jpg
A perspex door will cover the front to keep dust out. I'll need to get some hinges, magnetic strips and possibly some anti dust strips to fill gaps. The tube in this picture contains the diffuser conduit for the LEDs, in black.
You do not have the required permissions to view the files attached to this post.

Alex_W
Posts: 1700
Joined: Wed Apr 03, 2019 3:15 pm
Location: Pennsylvania
Contact:

Re: Upgrading my display cabinet

Post by Alex_W »

It's coming along nicely.

Tom
Posts: 29937
Joined: Fri Aug 23, 2013 9:29 am
Location: The Netherlands

Re: Upgrading my display cabinet

Post by Tom »

That looks like you'll be able to fit in lots of models.

rotormotor
Posts: 3633
Joined: Sat Dec 31, 2011 10:27 pm
Location: Wellington ~ New Zealand

Re: Upgrading my display cabinet

Post by rotormotor »

Looking great champ..

Wished i used a diffuser for my led strips in my cabinet.
Adhesive 3m tape backing i stuck to the underside of glass shelf to light things up but you do get the rows of led dots reflected on the vehicle rooves that wouldnt show being difused but not found a way of doing just that.
Lars

StevieSX
Posts: 269
Joined: Fri Sep 11, 2020 4:02 pm
Location: Ipswich
Contact:

Re: Upgrading my display cabinet

Post by StevieSX »

Alex_W wrote:
Sun Sep 05, 2021 12:51 pm
It's coming along nicely.
Thanks :)
Tom wrote:
Sun Sep 05, 2021 1:34 pm
That looks like you'll be able to fit in lots of models.
Hopefully about 330 models, so somewhere around half of the collection.
rotormotor wrote:
Mon Sep 06, 2021 12:10 am
Looking great champ..

Wished i used a diffuser for my led strips in my cabinet.
Adhesive 3m tape backing i stuck to the underside of glass shelf to light things up but you do get the rows of led dots reflected on the vehicle rooves that wouldnt show being difused but not found a way of doing just that.
Ahh, the diffuser strips will be screwed in to the top of the cabinet and provide good light, hopefully without being too harsh.

Post Reply